DIY Tub Installation.
DIY Tub Installation.
Blog Article
Presented here below you might get more great content concerning How to Install a Bathtub.
Mounting a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably difficult job. If the old bathtub is easily obtainable, the project can move easily; if you have to open up a wall surface to remove the old bathtub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you may need an expert plumber to make tube links.
This write-up will help you set up a brand-new bath tub in your washroom if you have already purchased a new bathtub and also do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also product list should consist of the following:
Removing Old Touches
If you need to replace old taps with new ones as a part of your installation, then the first thing you need to do is separate the water. After doing so, activate the faucets to drain any water remaining in the system. The process of removing the existing taps can be quite problematic due to the restricted access that is often the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from transforming throughout this process. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the maker provided backnut. As soon as the tap is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The previous type must be connected to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Utilizing both wooden boards under its feet, position the tub in the called for setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards instead of concentrating all the weight onto 4 small factors.
The following goal is to make sure that the bath tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bathtub till the spirit level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water system and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Finally, repair the bathroom paneling as described in the producer's user's manual. Tiling and also securing around the bathtub ought to wait up until the bath tub has been utilized a minimum of when as this will certainly settle it into its last placement.
Preparing for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to break a rigid seal, creating the water to pass through the wall between the bathroom and also the tiling, causing problems with dampness and also feasible leaks to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and installations. They are marketed in tubes as well as cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the activity experienced when the bathtub is in usage. The sealant can crack relatively early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is a good idea to fit the floor tiles making use of water-resistant or water-proof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader on A Step-by-Step Guide to Installing a Bathtub, I figured sharing that portion was a good idea. Enjoyed our post? Please share it. Help another person check it out. Thanks a lot for taking the time to read it.
Estimate Free Report this page